IDT Tsi578 User Manual Download | Manualshive

Page: 478 / 527

background image

13. I2C Registers > Register Descriptions

478

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

13.2.32

I2C_SCLK Low and Arbitration Timeout Register

This register programs the I2C_SCLK low timeout and the Arbitration timeout. The arbitration timer
period is relative to the MSDIV period, and the I2C_SCLK low timeout period is relative to the
USDIV period.

Register name: I2C_SCL_ARB_TIMEOUT

Reset value: 0x65BB_0033

Register offset: 0x1D354

Bits

0

1

2

3

4

5

6

7

00:07

SCL_TO

08:15

SCL_TO

16:23

ARB_TO

24:31

ARB_TO

Bits

Name

Description

Type

Reset

Value

00:15

SCL_TO

Count for I2C_SCLK Low Timeout Period

Defines the maximum amount of time for a slave device
holding the I2C_SCLK signal low. This timeout covers the
period from I2C_SCLK falling edge to the next I2C_SCLK
rising edge. Value 0x0 disables the timeout.

Period(SCL_TO) = (SCL_TO * Period(USDIV)) where
USDIV is the microsecond time defined in the

Period Divider Register”

The reset value of this timeout is 26,000 microseconds (26
milliseconds).

R/W

0x65BB

16:31

ARB_TO

Count for Arbitration Timeout Period

Defines the maximum amount of time for the master
interface to arbitrate for the bus before aborting the
transaction. This timeout covers the period from master
operation start (setting the START bit in the

Control Register”

) until the ACK/NACK is received from the

external slave for the slave device address. A value of 0
disables the timeout.

Period(ARB_TO) = (ARB_TO * Period(MSDIV)) where
MSDIV is the millisecond time defined in

Divider Register”

.

The reset value of this timeout is 51 milliseconds. However,
this timeout is not active during the boot load sequence.

R/W

0x0033

«
...
476
477
478
479
480
...
»

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

Brand: Gefen Pages: 11

xStack DES-3500 Series

Brand: D-Link Pages: 260

DXS-3600 Series

Brand: D-Link Pages: 48

DXS-3400 SERIES

Brand: D-Link Pages: 3

Web Smart Switch DGS-1210-16

Brand: D-Link Pages: 71

Brand: D-Link Pages: 3

Brand: D-Link Pages: 56

xStack DES-3800 Series

Brand: D-Link Pages: 326

xStack DES-3526

Brand: D-Link Pages: 222

Brand: D-Link Pages: 2

DXS-1210 Series

Brand: D-Link Pages: 20

Brand: Cabletron Systems Pages: 88

Brand: FANATEC Pages: 40

Brand: Xantech Pages: 20

Brand: Meridian Pages: 16

Brand: Tripp Lite Pages: 80

Brand: Watchguard Pages: 26

CRSMEO-4 Series

Brand: Festo Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands