IDT Tsi578 User Manual Download

Page: 432 / 527

13. I2C Registers > Register Descriptions

432

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

MA_COL

Master Collision

0 = Interrupt status not asserted

1 = Collision (arbitration loss) occurred following the device
address phase

A transaction initiated using the

“I

C Master Control

aborted due to loss of arbitration after the slave

device address phase. This indicates multiple masters tried
to access the same slave. This can also be set at the end of
boot load due to BL_FAIL.

R/W1C

MA_TMO

Master Timeout

0 = Interrupt status not asserted

1 = Transaction aborted due to timeout expiration

A transaction initiated using the

“I

C Master Control

aborted due to expiration of the clock low, byte, or

transaction time-outs. This can also be set at the end of boot
load due to BL_FAIL.

R/W1C

MA_NACK

Master NACK

0 = Interrupt status not asserted

1 = NACK received during transaction

A transaction initiated through the

“I

C Master Control

aborted due to receipt of a NACK in response to

slave address, peripheral address, or a written byte. This
can also be set at the end of boot load due to BL_FAIL.

R/W1C

MA_ATMO

Master Arbitration Timeout

0 = Interrupt status not asserted

1 = Bus arbitration timeout expired

A transaction initiated through the

“I

C Master Control

aborted due to expiration of the arbitration timeout

(see ARB_TO in

“I2C_SCLK Low and Arbitration Timeout

). This indicates the bus is in use by other masters.

R/W1C

MA_OK

Master Transaction OK

0 = Interrupt status not asserted

1 = Access completed and successful

A transaction initiated through the

“I

C Master Control

completed without error.

R/W1C

The write-1-to-clear (W1C) operation requires that this register first be read to create an event
snapshot.

(Continued)

Bits

Name

Description

Type

Reset

Value

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Search results

Summary of Contents for Tsi578

Reviews:

Related manuals for Tsi578

Brands by name

Popular brands

IDT Tsi578, User Manual

Search results

Summary of Contents for Tsi578

Reviews:

Related manuals for Tsi578

Brands by name

Popular brands