Hitachi SJ700D-004L, Instruction Manual

Page: 275 / 288

Chapter 8 List of Data Settings
8-10
Code Function name Monitored data or setting
Default
Memo
Change during
RUN operation
Page
FF FEF FUF b031 ≠ 10 b031=10
In
tel
lig
en
t o
u
tp
u
t
ter
m
in
al
s
C021
Terminal [11] function
00 (RUN: running), 01 (FA1: constant-speed reached),
02 (FA2: set frequency overreached),
03 (OL: overload notice advance signal (1)),
04 (OD: output deviation for PID control),
05 (AL: alarm signal),
06 (FA3: set frequency reached), 07 (OTQ: over-torque),
08 (IP: instantaneous power failure),
09 (UV: under voltage), 10 (TRQ: torque limited),
11 (RNT: operation time over), 12 (ONT: plug-in time over),
13 (THM: thermal alarm signal), 19(BRK:brakge release), 20(BER:braking
error)21 (ZS: 0 Hz detection signal), 22(DSE:speed deviation maximum),
23(POK:positioning completed),
24 (FA4: set frequency overreached 2),
25 (FA5: set frequency reached 2),
26 (OL2: overload notice advance signal (2)),
27 (Odc: Analog O disconnection detection),
28 (OIDc: Analog OI disconnection detection),
29 (O2Dc: Analog O2 disconnection detection),
31 (FBV: PID feedback comparison),
32 (NDc: communication line disconnection),
33 (LOG1: logical operation result 1),
34 (LOG2: logical operation result 2),
35 (LOG3: logical operation result 3),
36 (LOG4: logical operation result 4),
37 (LOG5: logical operation result 5),
38 (LOG6: logical operation result 6),
39 (WAC: capacitor life warning),
40 (WAF: cooling-fan speed drop),
41 (FR: starting contact signal),
42 (OHF: heat sink overheat warning),
43 (LOC: low-current indication signal),
44 (M01: general-purpose output 1),
45 (M02: general-purpose output 2),
46 (M03: general-purpose output 3),
47 (M04: general-purpose output 4),
48 (M05: general-purpose output 5),
49 (M06: general-purpose output 6),
50 (IRDY: inverter ready), 51 (FWR: forward rotation),
52 (RVR: reverse rotation), 53 (MJA: major failure),
54(WCO: window comparator O),
55(WCOI: window comparator OI),
56 (WCO2: window comparator O2)
(When alarm code output is selected for "C062", functions "AC0" to "AC2"
or "AC0" to "AC3" [ACn: alarm code output] are forcibly assigned to
intelligent output terminals 11 to 13 or 11 to 14, respectively.)
01 Not Allowed
4-60
C022
Terminal [12] function
00 Not Allowed
C023
Terminal [13] function
03 Not Allowed
C024 Terminal [14] function 07 Not Allowed
C025 Terminal [15] function 40 Not Allowed
C026 Alarm relay terminal function 05 Not Allowed
A
n
al
o
g m
o
n
it
o
ri
n
g
C027
[FM] siginal selection
00 (output frequency), 01 (output current),
02 (output torque), 03 (digital output frequency),
04 (output voltage), 05 (input power),
06 (electronic thermal overload), 07 (LAD frequency),
08 (digital current monitoring), 09 (motor temperature),
10 (heat sink temperature), 12 (general-purpose output YA0)
00 Not Allowed 4-73
C028 [AM] siginal selection
00 (output frequency), 01 (output current),
02 (output torque), 04 (output voltage), 05 (input power), 06 (electronic
thermal overload), 07 (LAD frequency),
09 (motor temperature), 10 (heat sink temperature),
11 (output torque [signed value]), 13 (general-purpose output YA1)
00 Not Allowed
4-74
C029
[AMI] siginal selection
00 (output frequency), 01 (output current),
02 (output torque), 04 (output voltage), 05 (input power), 06 (electronic
thermal overload), 07 (LAD frequency),
09 (motor temperature), 10 (heat sink temperature),
14 (general-purpose output YA2)
00 Not Allowed
C030
Digital current monitor
reference value 0.20 x "rated current" to 2.00 x "rated current" (A)
(Current with digital current monitor output at 1,440 Hz)
Rated current Allowed Allowed 4-73
In
tel
lig
en
t
o
u
tp
u
t
ter
mi
n
al
s
C031 Terminal [11] active state 00 (NO) / 01 (NC) 00 Not Allowed
4-61
C032
Terminal [12] active state 00 (NO) / 01 (NC)
00 Not Allowed
C033
Terminal [13] active state 00 (NO) / 01 (NC)
00 Not Allowed
C034 Terminal [14] active state 00 (NO) / 01 (NC) 00 Not Allowed
C035
Terminal [15] active state 00 (NO) / 01 (NC)
00 Not Allowed
C036
Alarm relay active state 00 (NO) / 01 (NC)
01 Not Allowed