Hitachi SJ700D-004L, Instruction Manual

Page: 269 / 288

Chapter 8 List of Data Settings
8-4
Code Function name Monitored data or setting
Default
Memo
Change during
RUN operation
Page
FF FEF FUF b031 ≠ 10 b031=10
V
/f
c
h
ar
ac
teri
st
ic
A041 Torque boost method selection
00 (manual torque boost),
01 (automatic torque boost)
00 Not Not
4-18
A241
Torque boost method selection, 2nd motor
00 Not Not
A042 Manual torque boost value
0.0 to 20.0 (%)
1.0 Allowed Allowed
A242 Manual torque boost value, 2nd motor 1.0 Allowed Allowed
A342
Manual torque boost value, 3rd motor
1.0 Allowed Allowed
A043 Manual torque boost frequency adjustment
0.0 to 50.0 (%)
5.0 Allowed Allowed
A243
Manual torque boost frequency adjustment,
2nd motor
5.0 Allowed Allowed
A343
Manual torque boost frequency adjustment,
3rd motor
5.0 Allowed Allowed
A044
V/F characteristic curve selection, 1st motor
00 (VC), 01 (VP), 02 (free V/f), 03 (sensorless vector control),
04 (0Hz sensorless vector control)(only CT),
05(vector with sensor)(only CT)
00 Not Not
4-16
A244 V/F characteristic curve selection, 2nd motor
00 (VC), 01 (VP), 02 (free V/f), 03 (sensorless vector control),
04 (0Hz sensorless vector control)(only CT)
00 Not Not
A344
V/F characteristic curve selection, 3rd motor 00(VC), 01(VP)
00 Not Not
A045 V/f gain setting 20. to 100. (%) 100. Allowed Allowed 4-15
A046
Voltage compensation gain setting for
automatic torque boost. 1st motor
0. to 255.
100. Allowed Allowed
4-18
A246
Voltage compensation gain setting for
automatic torque boost, 2nd motor
100. Allowed Allowed
A047
Slippage compensation gain setting for
automatic torque boost, 1st motor
0. to 255.
100. Allowed Allowed
A247
Slippage compensation gain setting for
automatic torque boost, 2nd motor
100. Allowed Allowed
D
C b
ra
ki
n
g
A051 DC braking enable 00 (disabling), 01 (enabling), 02 (set frequency only) 00 Not Allowed
4-20
A052
DC braking frequency setting 0.00 to 99.99, 100.0 to 400.0 (Hz)
0.50 Not Allowed
A053 DC braking wait time 0.0 to 5.0 (s) 0.0 Not Allowed
A054
DC braking force during deceleration
0. to 100. (%) <0. to 80. (%)> (In case of CT)
0. to 70. (%) <0. to 50. (%)> (In case of VT)
0.
Not Allowed
A055
DC braking time for deceleration 0.0 to 60.0 (s)
0.0 Not Allowed
A056
DC braking/edge or level detection
for [DB] input
00 (edge operation), 01 (level operation) 01 Not Allowed
A057
DC braking force for starting
0. to 100. (%) <0. to 80. (%)> (In case of CT)
0. to 70. (%) <0. to 50. (%)> (In case of VT)
0.
Not Allowed
A058
DC braking time for starting 0.0 to 60.0(s)
0.0 Not Allowed
A059 DC braking carrier frequency setting
0.5 to 15.0(kHz) <0.5 to 10.0 (kHz) > (In case of CT)
0.5 to 12.0(kHz) <0.5 to 8.0 (kHz) > (In case of VT)
5.0<3.0> (CT)
3.0 (VT)
Not Allowed
Fr
eq
u
en
cy
u
p
p
er/
lo
w
er
lim
it
an
d
ju
m
p
f
re
q
u
en
cy
A061
Frequency upper limit setting 0.00 or "1st minimum frequency limit" to "maximum frequency" (Hz)
0.00 Not Allowed
4-24
A261
Frequency upper limit setting, 2nd motor
0.00 or "2nd minimum frequency limit" to "maximum frequency,
2nd motor" (Hz)
0.00 Not Allowed
A062 Frequency lower limit setting 0.00 or "start frequency" to "maximum frequency limit" (Hz) 0.00 Not Allowed
A262
Frequency lower limit setting, 2nd motor 0.00 or "start frequency" to "maximum frequency, 2nd motor limit" (Hz)
0.00 Not Allowed
A063
Jump (center) frequency setting 1 0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00 Not Allowed
4-25
A064
Jump (hysteresis) frequency width setting 1 0.00 to 10.00 (Hz)
0.50 Not Allowed
A065
Jump (center) frequency setting 2 0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00 Not Allowed
A066 Jump (hysteresis) frequency width setting 2 0.00 to 10.00 (Hz) 0.50 Not Allowed
A067
Jump (center) frequency setting 3 0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00 Not Allowed
A068
Jump (hysteresis) frequency width setting 3 0.00 to 10.00 (Hz)
0.50 Not Allowed
A069 Acceleration stop frequency setting 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00 Not Allowed
A070
Acceleration stop time frequency setting 0.0 to 60.0 (s)
0.0 Not Allowed
PI
D
c
o
n
tr
o
l
A071
PID Function Enable 00 (disabling), 01 (enabling), 02 (enabling inverted-data output)
00 Not Allowed
4-26
A072
PID proportional gain 0.2 to 5.0
1.0 Allowed Allowed
A073
PID integral time constant 0.0 to 999.9, 1000. to 3600. (s)
1.0 Allowed Allowed
A074 PID derivative gain 0.00 to 99.99, 100.0 (s) 0.00 Allowed Allowed
A075
PV scale conversion 0.01 to 99.99
1.00 Not Allowed
A076 PV source setting
00 (input via OI), 01 (input via O), 02 (external communication),
03 (pulse-string frequency input), 10 (operation result output)
00 Not Allowed
A077
Output of inverted PID deviation 00(OFF), 01 (ON)
00 Not Allowed
A078 PID variation range 0.0 to 100.0 (%) 0.0 Not Allowed
A079
PID feed forward selection 00 (disabled), 01 (O input), 02 (OI input), 03 (O2 input)
00 Not Allowed
(Note) <>indicate the setting range of 75 to 150kW
(Note) CT : Constant torque mode, VT : Variable torque mode, you can set CT or VT by b049.