Hitachi SJ700D-004L, Instruction Manual

Page: 276 / 288

Chapter 8 List of Data Settings
8-11
Code Function name Monitored data or setting
Default
Memo
Change during
RUN operation
Page
FF FEF FUF b031 ≠ 10 b031=10
Lev
el
s an
d
o
u
tp
u
t
ter
m
in
al
s
ta
tu
s
C038
Low-current indication signal
output mode selection 00 (output during acceleration/deceleration and constant-speed
operation), 01 (output only during constant-speed operation)
01 Not Allowed
4-69
C039
Low-current indication signal
detection level
0.0 to 2.00 x "rated current" (A)
<0.0 to 1.80 x "rated current" (A) > (In case of CT)
0.0 to 1.50 x "rated current" (A) (In case of VT)
Rated current Allowed Allowed
C040
Overload signal output mode
00 (output during acceleration/deceleration and constant-speed
operation), 01 (output only during constant-speed operation)
01 Not Allowed
4-40
C041
Overload level setting
0.0 to 2.00 x "rated current" (A)
<0.0 to 1.80 x "rated current" (A) > (In case of CT)
0.0 to 1.50 x "rated current" (A) (In case of VT)
Rated current Allowed Allowed
C042
Frequency arrival setting for accel. 0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00 Not Allowed
4-62
C043
Frequency arrival setting for decel. 0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00 Not Allowed
C044 PID deviation level setting 0.0 to 100.0 (%) 3.0 Not Allowed 4-29
C045
Frequency arrival setting for
acceleration (2)
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00 Not Allowed
4-62
C046
Frequency arrival setting for
deceleration (2)
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00 Not Allowed
C052
Maximum PID feedback data 0.0 to 100.0 (%)
100.0 Not Allowed
4-29
C053
Minimum PID feedback data 0.0 to 100.0 (%)
0.0 Not Allowed
C055
Over-torque (forward-driving) level
setting
0. to 200. (%) <0. to 180. (%)>
100. Not Allowed
4-65
C056
Over-torque (reverse regenerating)
level setting
0. to 200. (%) <0. to 180. (%)>
100. Not Allowed
C057
Over-torque (reverse driving) level
setting
0. to 200. (%) <0. to 180. (%)>
100. Not Allowed
C058
Over-torque (forward
regenerating) level setting
0. to 200. (%) <0. to 180. (%)>
100. Not Allowed
C061
Electronic thermal warning level
setting
0. to 100. (%)
80. Not Allowed 4-38
C062 Alarm code output 00 (disabling), 01 (3 bits), 02 (4 bits) 00 Not Allowed 4-65
C063
Zero speed detection level 0.00 to 99.99, 100.0 (Hz)
0.00 Not Allowed 4-64
C064
Heat sink overheat warning level 0. to 200.0 (

C)
120. Not Allowed 4-68
Co
m
m
u
n
ic
at
io
n
f
u
n
ct
io
n
C071
Communication speed selection
02 (loopback test), 03(2400bps), 04(4800bps),
05(9600bps), 06(19.2kbps), 07(38.4kbps),
08(57.6kbps), 09(76.8kbps), 10(115.2kbps)
04 Not Allowed
4-113
C072
Node allocation 1. to 247.
1. Not Allowed
C073
Communication data length
selection
7 (7 bits), 8 (8 bits)
7 Not Allowed
C074 Communication parity selection 00 (no parity), 01 (even parity), 02 (odd parity) 00 Not Allowed
C075
Communication stop bit selection 1 (1 bit), 2 (2 bits)
1 Not Allowed
C076
Selection of the operation after
communication error
00 (tripping), 01 (tripping after decelerating and stopping the
motor), 02 (ignoring errors), 03 (stopping the motor after
free-running), 04 (decelerating and stopping the motor)
02 Not Allowed
C077
Communication timeout limit
before tripping
0.00 to 99.99 (s)
0.00 Not Allowed
C078 Communication wait time 0. to 1000. (ms) 0. Not Allowed
C079
Communication mode selection 00(ASCII), 01(Modbus-RTU)
00 Not Allowed
A
d
ju
st
m
en
t
C081
[O] input span calibration
0. to 9999., 1000 to 6553(10000 to 65530)
Factory setting Allowed Allowed

C082
[OI] input span calibration
Factory setting Allowed Allowed
C083
[O2] input span calibration
Factory setting Allowed Allowed
C085 Thermistor input tuning 0.0 to 999.9, 1000. Factory setting Allowed Allowed 4-72
C091
Debug mode enable
(Do not change this parameter, which is intended for factory
adjustment.)
00 Not Not

O
th
e
rs
C101
Up/Down memory mode selection 00 (not storing the frequency data), 01 (storing the frequency data)
00 Not Allowed 4-56
C102
Reset mode selection
00 (resetting the trip when RS is on),
01 (resetting the trip when RS is off),
02 (enabling resetting only upon tripping [resetting when RS is on]),
03(resetting only trip)
00 Allowed Allowed
4-54
C103
Restart mode after reset
00 (starting with 0 Hz), 01 (starting with matching frequency),
02 (restarting with active matching frequency)
00 Not Allowed
M
et
er
a
d
ju
st
ment
C105
FM gain adjustment
50. to 200. (%)
100. Allowed Allowed 4-73
C106
AM gain adjustment
100. Allowed Allowed
4-74
C107 AMI gain adjustment 100. Allowed Allowed
C109
AM bias adjustment
0. to 100. (%)
0. Allowed Allowed
C110
AMI bias adjustment
20. Allowed Allowed
(Note) <>indicate the setting range of 75 to 150kW
(Note) CT : Constant torque mode, VT : variable torque mode, you can set CT or VT by b049.