Hitachi SJ700D-004L, Instruction Manual

Page: 274 / 288

Chapter 8 List of Data Settings
8-9
Code Function name Monitored data or setting
Default
Memo
Change during
RUN operation
Page
FF FEF FUF b031 ≠ 10 b031=10
In
tel
lig
en
t i
n
p
u
t
ter
m
in
al
s
C001 Terminal [1] function (*2)
01 (RV: Reverse RUN), 02 (CF1: Multispeed 1 setting),
03 (CF2: Multispeed 2 setting),
04 (CF3: Multispeed 3 setting),
05 (CF4: Multispeed 4 setting), 06 (JG: Jogging),
07 (DB: external DC braking),
08 (SET: Set 2nd motor data),
09 (2CH: 2-stage acceleration/deceleration),
11 (FRS: free-run stop), 12 (EXT: external trip),
13 (USP: unattended start protection),
14: (CS: commercial power source enable),
15 (SFT: software lock),
16 (AT: analog input voltage/current select),
17 (SET3: 3rd motor control), 18 (RS: reset),
20 (STA: starting by 3-wire input),
21 (STP: stopping by 3-wire input),
22 (F/R: forward/reverse switching by 3-wire input),
23 (PID: PID disable), 24 (PIDC: PID reset),
26 (CAS: control gain setting),
27 (UP: remote control UP function),
28 (DWN: remote control DOWN function),
29 (DWN: remote control data clearing),
31 (OPE: forcible operation), 32 (SF1: multispeed bit 1),
33 (SF2: multispeed bit 2), 34 (SF3: multispeed bit 3),
35 (SF4: multispeed bit 4), 36 (SF5: multispeed bit 5),
37 (SF6: multispeed bit 6), 38 (SF7: multispeed bit 7),
39 (OLR: overload restriction selection),
40 (TL: torque limit enable),
41 (TRQ1: torque limit selection bit 1),
42 (TRQ2: torque limit selection bit 2),
43 (PPI: P/PI mode selection), 44(BOK:braking confirmation),
46 (LAC: LAD cancellation),
47(PCLR:clearance of position deviation)
48(STAT:pulse train position command input enable)
50 (ADD: trigger for frequency addition [A145]),
51 (F-TM: forcible-terminal operation),
52(ATR:permision of torque command input),
53 (KHC: cumulative power clearance),
54(SON:servo-on), 55(FOC:pre-excitation),
56 (MI1: general-purpose input 1),
57 (MI2: general-purpose input 2),
58 (MI3: general-purpose input 3),
59 (MI4: general-purpose input 4),
60 (MI5: general-purpose input 5),
61 (MI6: general-purpose input 6),
62 (MI7: general-purpose input 7),
63 (MI8: general-purpose input 8),
64(EMR: Emergency stop signal),
65 (AHD: analog command holding),
66(CP1:multi stage position settings selection 1),
67(CP2:multi stage position settings selection 2),
68(CP3:multi stage position settings selection 3),
69(ORL:Zero-return limit function),
70(ORG:Zero-return trigger function),
71(FOT:forward drive stop),72(ROT:reverce drive stop),
73(SPD:speed/position switching),
74 (PCNT: pulse counter), 75 (PCC: pulse counter clear),
82(PRG:EzSQ program-run terminal),
no (NO: no assignment)
18
(*2)
Not Allowed
4-46
C002
Terminal [2] function
16 Not Allowed
C003
Terminal [3] function (*2)
06
(*2)
Not Allowed
C004 Terminal [4] function 11 Not Allowed
C005
Terminal [5] function
09 Not Allowed
C006
Terminal [6] function
03 03 13 Not Allowed
C007 Terminal [7] function 02 Not Allowed
C008
Terminal [8] function
01 Not Allowed
C011
Terminal [1] active state 00 (NO) / 01 (NC)
00 Not Allowed
4-47
C012 Terminal [2] active state 00 (NO) / 01 (NC) 00 Not Allowed
C013
Terminal [3] active state 00 (NO) / 01 (NC)
00 Not Allowed
C014
Terminal [4] active state 00 (NO) / 01 (NC)
00 Not Allowed
C015 Terminal [5] active state 00 (NO) / 01 (NC) 00 Not Allowed
C016
Terminal [6] active state 00 (NO) / 01 (NC)
00 00 01 Not Allowed
C017
Terminal [7] active state 00 (NO) / 01 (NC)
00 Not Allowed
C018 Terminal [8] active state 00 (NO) / 01 (NC) 00 Not Allowed
C019
Terminal [FW] active state 00 (NO) / 01 (NC)
00 Not Allowed
*2 When the emergency stop function is enabled (SW1 = ON), "18" (RS) and "64" (EMR) are forcibly written to parameters "C001" and "C003", respectively. (You
cannot arbitrarily write "64" to "C001".) If the SW1 signal is turned off and then turned on, "no" (no assignment) is set in parameter "C003".