Index
Index - 3
OPE ..................................................................... 3-3, 4-51
operating methods ...................................................... 3-1
operation after option error...................................... 4-79
operation frequency.................................................. 4-13
operation mode ........................................................ 4-33
operation time over signal (RNT)/plug-in
time over signal (ONT) ............................... 4-59, 4-64
operator ........................................................... 4-13, 4-66
ORG ......................................................................... 4-109
ORL .......................................................................... 4-109
ORT ............................................................... 4-104, 4-110
OTQ ........................................................................... 4-65
output current monitoring .......................................... 4-1
output frequency monitoring...................................... 4-1
output frequency setting ............................................ 4-7
output phase loss .................................................... 4-36
output phase loss protection .................................. 4-36
output signal delay/hold ........................................... 4-72
output voltage monitoring .......................................... 4-3
overcurrent restraint ................................................. 4-40
overload notice advance signal ................................. 4-40
overload restriction ................................................... 4-40
overtorque ................................................................ 4-65
over voltage supression............................................. 4-41
P
P/PI switching ............................................................ 4-58
P24 2-7, 2-21
PCC ............................................................................ 4-59
PCLR .......................................................................... 4-96
PCNT ................................................................... 4-5, 4-59
PID 4-26
PIDC ........................................................................... 4-29
POK.......................................................................... 4-104
positioning completed ............................................ 4-104
position bias ............................................................ 4-103
position command monitor ........................................ 4-5
position range specification .......................... 4-106,4-110
power monitoring ....................................................... 4-3
PPI 4-59
process variable (PV), PID feedback
monitoring ................................................... 4-1, 4-29
program counter ......................................................... 4-5
program number monitoring ...................................... 4-5
programming error monitoring ................................... 4-6
programmable controller .......................................... 2-22
protective function ...................................................... 5-1
pulse counter ..................................................... 4-5, 4-59
pulse train frequency input ..................................... 4-112
pulse train position command .................................. 4-99
R
reduced-torque characteristic (electronic
thermal) .............................................................. 4-37
reduced torque characteristic (VP) ............................ 4-16
reduced voltage start ................................................ 4-43
remote operation ...................................................... 4-56
remote operator ............................................. Appendix-1
reset .....................................................2-9, 3-3, 4-9, 4-54
restart with input frequency ............................ 4-33, 4-36
retry after trip ........................................................... 4-33
retry selection ...........................................................4-33
reverse rotation signal ...................................... 4-60,4-70
reversible ......................................................... 4-13, 4-28
RNT ............................................................................4-64
ROT ..........................................................................4-110
rotation direction minitoring .......................................4-1
rotational direction restriction ....................................4-7
RS ....................................................................... 2-9, 4-54
RUN ............................................................ 3-3, 4-4, 4-62
running time over / power-on time over ...................4-64
run command source setting .......................................4-8
running signal ............................................................ 4-62
RV ....................................................................... 4-8,4-46
RVR .......................................................................... 4-70
S
scaled output frequency monitoring ...........................4-2
2nd/3rd control ..........................................................4-50
secondary resistance compensation ......................... 4-87
sensorless vector control ................................. 4-16, 4-89
servo-on ..................................................................4-111
SET, SET3 ....................................................................4-50
SFT 4-51
SF1, SF2, SF3, SF4, SF5, SF6, SF7 ................................ 4-47
sign of the frequency to be added .............................4-14
sink logic ....................................................................2-21
SJ300 ............................................................. Appendix-1
slide switch SW1 ..................................... 2-9, Appendix-1
SLV 4-16
software lock .............................................................4-51
SON .........................................................................4-111
source logic................................................................2-20
SPD ..........................................................................4-108
speed deviation maximum ........................................4-96
speed biasing ...........................................................4-103
speed/position switching ........................................4-108
STA 4-57
stabilization constant.................................................4-79
start/end frequency setting for external
analog input ........................................................4-14
start frequency ..........................................................4-41
start-frequency rate ...................................................4-14
starting contact signal ...............................................4-68
start with matching frequency ........................ 4-33, 4-52
STAT ...........................................................................4-96
stop operation selection ..............................................4-9
STOP/RESET key selection ............................................4-9
STP 4-57
synchronous operation ............................................ 4-102
T
teaching ...................................................................4-106
test run ......................................................................3-10
thermistor ........................................... 2-8,4-4, 4-72,4-87
THM ...........................................................................4-39
3-wire input ............................................................... 4-57
TL ............................................................................... 4-92
torque bias monitoring ................................................4-3
torque biasing ............................................................4-98
torque boost .................................................... 4-17, 4-18
torque command monitoring ......................................4-3
Summary of Contents for SJ700D-004L
