Hitachi SJ700D-004L, Instruction Manual

Page: 117 / 288

Chapter 4 Explanation of Functions
4-46
4.2.39 Intelligent input terminal setting
You can assign the functions described below to intelligent input terminals
[1] to [8]. To assign the desired functions to the terminals, specify the
desired data listed in the table below for terminal settings "C001" to
"C008". For example, "C001" corresponds to intelligent input terminal [1].
You can select the a-contact or b-contact input for individual intelligent input terminals.
You can assign one function only to an intelligent input terminal. If you have attempted to assign a function to two or
more intelligent input terminals, the function is assigned to only the terminal to which you have last attempted
assignment. Function data "NO" (no assign) is assigned to other terminals, and those terminals are ineffective in terms
of functions.
After assigning the desired functions to intelligent input terminals [1] to [8], confirm that the assigned functions have
been stored on the inverter.
Data Description Reference item
Availability(Yes or No)
Page
CT mode VT mode
01 RV: Reverse RUN command Operation command
Y Y
－
02 CF1: Multispeed 1 setting (binary operation)
Multispeed operation function
Y Y
4-48
03 CF2: Multispeed 2 setting (binary operation)
Y Y
04 CF3: Multispeed 3 setting (binary operation)
Y Y
05 CF4: Multispeed 4 setting (binary operation) Y Y
06 JG: Jogging Jogging operation function Y Y 4-50
07 DB: External DC braking DC braking (external DC braking) function Y Y 4-20
08 SET: Set 2nd motor data 2nd/3rd motor control function Y Y 4-50
09 2CH: 2-stage acceleration/deceleration 2-stage acceleration/deceleration function Y Y 4-30
11 FRS: Free-run stop Free-run stop function Y Y 4-53
12 EXT: External trip External trip function Y Y 4-58
13 USP: Unattended start protection Unattended start protection function Y Y 4-57
14 CS: Commercial power source enable Commercial power supply switching function Y Y 4-54
15 SFT: Software lock (control circuit terminal block) Software lock function Y Y 4-52
16 AT: Analog input voltage/current select External analog input setting function
Y Y
4-12
17 SET3: 3rd motor control 2nd/3rd motor control function Y Y 4-51
18 RS: Reset Reset Y Y 4-55
20 STA: Starting by 3-wire input
3-wire input function
Y Y
4-58 21 STP: Stopping by 3-wire input Y Y
22 F/R: Forward/reverse switching by 3-wire input Y Y
23 PID: PID disable
PID function
Y Y
4-26
24 PIDC: PID reset Y Y
26 CAS: Control gain setting Control gain switching function Y Y 4-59
27 UP: Remote control UP function
Remote control (UP/DWN) function
Y Y
4-57 28 DWN: Remote control DOWN function Y Y
29 DWN: Remote control data clearing Y Y
31 OPE: Forcible operation Forcible-operation function Y Y 4-52
32 SF1: Multispeed 1 setting (bit operation)
Multispeed operation function
Y Y
4-48
33 SF2: Multispeed 2 setting (bit operation) Y Y
34 SF3: Multispeed 3 setting (bit operation) Y Y
35 SF4: Multispeed 4 setting (bit operation) Y Y
36 SF5: Multispeed 5 setting (bit operation)
Y Y
37 SF6: Multispeed 6 setting (bit operation)
Y Y
38 SF7: Multispeed 7 setting (bit operation) Y Y
39 OLR: Overload restriction selection Overload restriction function Y Y 4-40
40 TL: Torque limit enable
Torque limitation function
Y Y
4-93 41 TRQ1: Torque limit selection bit 1 Y Y
42 TRQ2: Torque limit selection bit 2 Y Y
43 PPI: P/PI mode selection P/PI switching function Y Y 4-59
44 BOK: Braking confirmation Brake control function Y N 4-82
45 ORT: Orientation Orientation function Y N 4-105
46 LAC: LAD cancellation LAD cancellation function
Y Y
4-10
47 PCLR: Clearance of position deviation
V2 control mode selection function
Y N
4-97
48 STAT: Pulse train position command input enable
Y N
50 ADD: Trigger for frequency addition (A145) Frequency addition function Y Y 4-14
C001 to C008: Terminal [1] to [8] functions
Related code