Chapter 4
Explanation of Functions
4-4
4.1.14 Cumulative power monitoring
When the cumulative power monitoring function is selected, the inverter
displays the cumulative value of electric power input to the inverter.
You can also convert the value to be displayed to gain data by setting the
cumulative input power display gain setting (b079).
Value displayed by function "d015" = "calculated value of input power (kW/h)"/"cumulative input power display gain
setting (b079)" The cumulative power input gain can be set within the range 1 to 1000 in steps of 1.
You can clear the cumulative power data by specifying "01" for the cumulative power clearance function (b078) and
pressing the STR key.
You can also clear the cumulative power data at an intelligent input terminal by assigning function "53" (KHC:
cumulative power clearance) to the intelligent input terminal.
When the cumulative input power display gain setting (b079) is set to "1000", the cumulative power data up to 999000
(kW/h) can be displayed.
(Display)
0.0 to 999.9 in steps of 1 kW/h, or the unit set for function "b079"
1000 to 9999 in units of 10 kW/h, or the unit set for function "b079"
100 to
999 in units of 1000 kW/h, or the unit set for function "b079"
4.1.15 Cumulative operation RUN time monitoring
When the cumulative operation RUN time monitoring function (d016) is elected,
the inverter displays the cumulative time of the inverter operation.
(Display)
0. to 9999. in units of 1 hour
1000 to 9999 in units of 10 hours
100 to
999 in units of 1,000 hours
4.1.16 Cumulative power-on time monitoring
When the cumulative power-on time monitoring function(d017) is selected,
the inverter displays the cumulative time throughout which the inverter power has been on.
(Display)
0. to 9999. in units of 1 hour
1000 to 9999 in units of 10 hours
100 to
999 in units of 1,000 hours
4.1.17 Heat sink temperature monitoring
When the heat sink temperature monitoring function (d018) is selected, the inverter
displays the temperature of the internal heat sink of the inverter.
(Display)
0.0 to 200.0 in steps of 0.1 °C
4.1.18 Motor temperature monitoring
When the motor temperature monitoring function is selected, the inverter
displays the temperature of the thermistor connected between control circuit
terminals TH and CM1.Use the thermistor model PB-41E made by Shibaura
Electronics Corporation. Specify "02" (enabling NTC) for the thermistor for
thermal protection control (function "b098").
(Display)
0.0 to 200.0 in steps of 0.1 °C.
Note: If "01" (enabling PTC) is specified for the thermistor for thermal protection control (function "b098"), motor
temperature monitoring is disabled.
4.1.19 Life-check monitoring
When the life-check monitoring function (d002) is selected, the inverter displays
the operating life status of two inverter parts output from corresponding
intelligent output terminals by using LED segments of the monitor.
The two targets of life-check monitoring are:
1: Life of the capacitor on the main circuit board
2: Degradation of cooling fan speed
d015: Cumulative power monitoring
b078: Cumulative power clearance
b079: Cumulative input power display gain
setting
Related code
d019: Motor temperature monitoring
b098: Thermistor for thermal
protection control
Related code
d022: Life-check monitoring
Related code
1
2
Life check
Normal
d016: Cumulative operation
RUN time monitoring
Related code
d017: Cumulative power-on
time monitoring
Related code
d018: Heat sink temperature
monitoring
Related code
Summary of Contents for SJ700D-004L
