ComAp ID-FLX-Lite-PC Global Manual Download Page 91

Page: 91 / 211

InteliDrive Lite - 1.2.1 Global guide

9 Function description

9.1 Engine operation states

9.2 OFF mode

9.3 MAN mode

9.4 AUT mode

9.5 Engine without pickup operation

9.6 Engine timer

9.7 Protections

9.8 Engine RPM control in MAN mode

9.9 AUT mode: Engine load limitation - overview

9.10 AUT mode: Engine regulation by RPM control - overview

104

back to Table of contents

9.1 Engine operation states

Engine State

Meaning

Init

Auto test during controller power on

Not ready

Engine is not ready to start

Prestart

Prestart sequence in process, Prestart output is closed

Cranking

Engine is cranking

Pause

Pause between start attempts

Starting

Starting RPM is reached, Idle RPM is not yet reached

Idle

Idle RPM is reached and the Idle timer is running

Running

Idle timer elaspsed, Engine is running at nominal speed

Stop

Shutdown

Shut-down alarm activated

Ready

Engine is ready to run

Cooling

Engine is cooling before stop

EmergMan

Emergency Manual engine operation

AfterCool

Engine after cooling - Cooling Pump output is closed

9.2 OFF mode

No start of the engine is possible. Outputs STARTER and FUEL SOLENOID are not energized. No reaction if

buttons are pressed.

9.3 MAN mode

- starts the engine.

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands

ComAp ID-FLX-Lite-PC, Global Manual

Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands