manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 62

InteliDrive Lite - 1.2.1 Global guide

62

Horn

The output closes if:

any warning or shutdown comes up or

the engine malfunctions

The output opens if:

FAULT RESET is pressed or

HORN RESET is pressed or

Max time of LBO HORN is exceeded (Horn timeout)

The output closes again if a new fault comes up.

Ready

The output is closed if following conditions are fulfilled:

Engine is not running and

No Shut down or Slow stop alarm is active

Controller is not in OFF mode

Ready to load

The output is closed if engine is running and no alarm is active - it is possible to close load. The output opens

when Wrn Underspeed protection is active and during cooling state.

Running

Output closes if the engine is in Running state.

Cooling

The output closes when engine is in Cooling state.

Fault Reset

One second pulse as echo for panel Fault reset button.

ChrgAlternFail

Output closes if engine is running and D+ input not energized.

The output opens, if

alarm is not active and

FAULT RESET is pressed

Note:

Threshold level for D+ input is 80% supply voltage.

Stop failed

Output closes when the engine has to be stopped, but speed or oil pressure is detected. This protection goes

active 60 s after stop command.

The output opens, if

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands