manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 79

InteliDrive Lite - 1.2.1 Global guide

79

7.1.4 Shut down (Sd)

When the shutdown alarm comes up, InteliDrive IPC opens all outputs e.g. FUEL SOLENOID, STARTER and

PRESTART to stop the engine immediately. Alarm outputs and common shutdown output are closed. Active or

not reset protection disables start.

Note:

Engine running only alarms are activated after

Engine protect

: Eng prot del, after the engine RPM >

Engine params

: Starting RPM during the engine starting procedure.

Note:

If LBI Sprinkler is active engine does not react on shutdown protection only for Emergency stop and

Overspeed protection.

7.1.5 List of possible alarms

Events

specification

Protection

type

Information

on binary

output

available

Description

Wrn Oil Press

WRN

YES

Oil pressure is smaller than Wrn Oil

press setpoint.

Sd Oil Press

SD

YES

Oil pressure is smaller than Sd Oil

press setpoint.

Sd NotOilPress

SD

YES

No information about the oil pressure

from the binary oil pressure sensor.

Wrn Engine Temp

WRN

YES

Water temperature is greater than Wrn

Water temp setpoint.

Sd Engine Temp

SD

YES

Water temperature is greater than Sd

Water temp setpoint.

Wrn Fuel Level

WRN

YES

Fuel level is smaller than Wrn Fuel

Level setpoint.

Sd Fuel Level

SD

YES

Fuel level is smaller than Sd Fuel

Level setpoint.

Ubat

WRN

YES

Battery voltage is out of limits given

by Batt overvolt and Batt undervolt

setpoints.

Wrn AIN

WRN

YES

Warning alarm configurable on the

input of the controller

Sd AIN

SD

YES

Shutdown alarm configurable on the

input of the controller.

Wrn AIO

WRN

YES

Warning alarm configurable on the

input of plug-in.

Sd AIO

SD

YES

Shutdown alarm configurable on the

input of plug-in.

Binary input

Configurable

YES

Configurable Warning/Shutdown

alarms on the inputs of InteliDrive IPC

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands