manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 168

InteliDrive Lite - 1.2.1 Global guide

168

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

0 - 10000 [U17]

Default value

10 U17

Force value

Step

1 U17

Comm object

13357

Related applications

Config level

Standard

Setpoint visibility

Always

Description

High ShutDown limit level for AIN5

Setpoint name depends on setting of AIN5 (maximum length is 14 characters).

AIN5 HighSd

6

back to List of setpoints

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

0 - 3600 [s]

Default value

10 s

Force value

Step

1 s

Comm object

13358

Related applications

Config level

Standard

Setpoint visibility

Always

Description

High level protection delay for Wrn and Sd of AIN5

Setpoint name depends on setting of AIN5 (maximum length is 14 characters).

Note:

Analog input 5 is fully configurable and it is voltage type of input with range 0-40V

AIN5 HighDel

6

back to List of setpoints

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

[-]

Default value

ENABLED

Force value

Step

[-]

Comm object

14658

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The setting DISABLED disables all configured protections, except Overspeed and Emergency Stop. It is

indicated in the alarm list by warning Prot AIN6 dis. Each configuration change is recorded in history,

records: Prot AIN6 dis and Prot AIN6 ena.

Setpoint name depends on setting of AIN6 (maximum length is 14 characters).

AIN6 prot

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands