manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 130

InteliDrive Lite - 1.2.1 Global guide

130

Setpoint group

Engine params

Related FW

1.2.1

Range [units]

1 - 60 [s]

Default value

10 s

Force value

Step

1 s

Comm object

8257

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Pause between crank (engine start) attempts.

CrnkFail pause

6

back to List of setpoints

Setpoint group

Engine params

Related FW

1.2.1

Range [units]

1 - 10 [-]

Default value

3

Force value

Step

1

Comm object

8255

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Maximum number of crank (engine start) attempts.

Crank attempts

6

back to List of setpoints

Setpoint group

Engine params

Related FW

1.2.1

Range [units]

0 - 60 [s]

Default value

0 s

Force value

Step

1 s

Comm object

14687

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The condition oil pressure >

Starting POil

is considered fulfilled after

Start POil Del

.

Note:

This parameter can be used for complete disabling of oil pressure engine running condition.

Therefore, this adjustment must be done very carefully.

Start POil Del

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands