ComAp ID-FLX-Lite-PC Global Manual Download Page 13

Page: 13 / 211

InteliDrive Lite - 1.2.1 Global guide

Image 2.3 Access verification page

4. Enter access code and Scada page appears

Image 2.4 Scada page

Note:

You can try the WebServer from ComAp webpage. The access code is 0.

Note:

WebSupervisor is possible to use as a control and monitor tool. For access is necessary to be registered.

Connection setting and other information you can find in the WebSupervisor Reference Guide.

2.3.3 Open connection from WinScope

WinScope is powerful PC tool for observation of controller’s states and measurements.

1. Go to menu

Connection

→

Open connection...

and select the type of connection you desire in Open

connection window (Inteli controllers).

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands

ComAp ID-FLX-Lite-PC, Global Manual

Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands