manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 162

InteliDrive Lite - 1.2.1 Global guide

162

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

[-]

Default value

ENABLED

Force value

Step

[-]

Comm object

14656

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The setting DISABLED disables all configured protections, except Overspeed and Emergency Stop. It is

indicated in the alarm list by warning Prot AIN4 dis. Each configuration change is recorded in history,

records: Prot AIN4 dis and Prot AIN4 ena.

Setpoint name depends on setting of AIN4 (maximum length is 14 characters).

AIN4 prot

6

back to List of setpoints

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

0 - 10000 [U16]

Default value

20 U16

Force value

Step

1 U16

Comm object

9271

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Warning limit level for AIN4

Setpoint name depends on setting of AIN4 (maximum length is 14 characters).

AIN4 Wrn

6

back to List of setpoints

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

0 - 10000 [U16]

Default value

10 U16

Force value

Step

1 U16

Comm object

9272

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Shutdown limit level for AIN4

Setpoint name depends on setting of AIN4 (maximum length is 14 characters).

AIN4 Sd

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands