manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 155

InteliDrive Lite - 1.2.1 Global guide

155

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

Starting RPM - 100 [%]

Default value

25 %

Force value

Step

1 % of nominal RPM

Comm object

8260

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Limit for Warning Underspeed protection. Active protection is indicated as “Wrn Underspeed” in Alarm list.

Under speed Warning protection is inactive 5s after RPM is over

Engine params

: Starting RPM and during

the Idle time.

The “Ready to load” output is deactivated when Wrn underspeed protection is active and needs the Fault

reset for activation after RPM is over Underspeed limit.

Underspeed

6

back to List of setpoints

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

0 - 600 [s]

Default value

30 s

Force value

Step

1 s

Comm object

12620

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Engine is switched to Cooling state when Binary input FlowSwitch is not closed within Flow SwitchDel after

„Running“ (Ready to load) engine state activation.

Flow SwitchDel

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands