manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 102

InteliDrive Lite - 1.2.1 Global guide

102

Reg Gain

Reg Integral

Engine load limitation with analog output

Purpose: Protect the engine against overload by reducing the load.

Description: The engine load (e.g. feeder speed) is reduced when actual “Percentual load” (coming from ECU) is

over the

Load limit

: LoadRequest1 (or LoadRequest2) setpoint. Load can be continuously reduced by Analog

output or switched between two levels by Binary output to keep the Engine load on or below the limit.

Input

J1939 - Actual Load in %

Binary input: L Request 2 (optional)

Binary input: Reg Disable (optional)

Output

Analog output: Load LimitAnOut (plug-in module)

Note:

LoadLimitAnOut range = 0 - 10000

Setpoints

Load limit:

Load Input = Load

Load Bias

Load Request

Load Request 2

Load ReqRamp

Load UpLimit

Load DownLimit

Load Gain

Load Integral

General comparator

Purpose: Switch on/off some device depends on analog value - e.g. temperature.

Description: The function activates/deactivates some device based e.g. on temperature.

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands