manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 44

InteliDrive Lite - 1.2.1 Global guide

44

DOWN

button. Use this button to move down or decrease value

of selected setpoint.

ENTER

button. Use this button to finish editing a setpoint or

moving right in the history page.

RUNNING LED

ALARM LED

5.2 Init screens

5.2.1 Init screen

This is a first screen after controller’s start which is dedicated for information provided by customers such as

contact numbers, service technician contact and customer message for end users of engine. Configuration of

this screen is only done by LiteEdit PC tool.

Note:

Init (welcome) screen appears immediately after power on with ComAp default text. It is possible to

modify it using LiteEdit – Configuration – Init button. There is space for 8 text lines per 21 ASCII characters

each.

5.2.2 Firmware screen

This screen contains information about controller’s type, controller manufacturer ComAp, uploaded firmware,

version of firmware, used application and branch. There is also information about currently configured electronic

engine unit, respectively about ESF file. Details for recognition of configured electronic engine are in chapter

ECU controlled engine support.

Note:

To see firmware information use panel buttons: hold ENTER and press PAGE. This procedure activates

the panel LEDs test as well. The screen disappears itself after app 5 seconds.

5.2.3 Languages screen

InteliDrive IPC controller offers configurable language support. On this screen is possible to switch between

languages configured in controller. Second way, how to change language, is by binary input Lang Selection.

Note:

To switch to Language screen use panel buttons: hold ENTER and press PAGE twice. Press ENTER to

leave this screen.

5.2.4 User interface screen

InteliDrive IPC controller enables to choose the user interface as customer prefers.

There are two choices available: USER or ENGINEER interface

USER

interface is simple menu displaying just measurement, alarm and init screens.

ENGINEER

interface allow changing the controller’s settings, reviewing the history, measurements and

alarms. This mode is default.

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands