manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 132

InteliDrive Lite - 1.2.1 Global guide

132

Setpoint group

Engine params

Related FW

1.2.1

Range [units]

[-]

Default value

IDLE

Force value

Step

[-]

Comm object

10046

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Selects the function of the Binary output IDLE/NOMINAL during engine Cooling state

IDLE: Cooling is executed at Idle speed.

NOMINAL: Cooling is executed at Nominal speed. Default state.

Note:

Binary output IDLE/NOMINAL must be configured and connected to speed governor. Engine Idle

speed must be adjusted on speed governor.

Cooling speed

6

back to List of setpoints

Setpoint group

Engine params

Related FW

1.2.1

Range [units]

0 - 3600 [s]

Default value

30 s

Force value

Step

1 s

Comm object

8258

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Run time of the unloaded engine to cool the engine before stop.

Cooling time

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands