manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 12

InteliDrive Lite - 1.2.1 Global guide

12

Note:

For internet connection enter controller adress, IP adress of the IB-LITE Module fitted in the

controller you want to reach, acces code

3. You will see the Control window and you can continue with configuration of setpoints, inputs, outputs etc.

Image 2.2 LiteEdit control window

Note:

For detail description of LiteEdit and InteliMonitor PC tools see the LiteEdit Reference Guide,

InteliMonitor Reference Guide and InteliDrive Communication Guide

2.3.2 Open connection from web browser

It is possible to connect from a web browser to InteliDrive IPC controllers, mounted with IB-Lite module (or IB-

NT with specific conditions) and connected to internet.

1. Open web browser

2. Enter IP address from controller

Comms Settings:

IBLite IP Addr

3. Access verification page appears

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands