manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 113

InteliDrive Lite - 1.2.1 Global guide

113

10.1.3 Group: Password

Note:

Following setpoints are available from Controller and LiteEdit/InteliMonitor.

Setpoint group

Password

Related FW

1.2.1

Range [units]

[-]

Default value

[-]

Force value

Step

[-]

Comm object

[-]

Related applications

Config level

Standard

Setpoint

visibility

Always

Description

Password is a four-digit number. Password enables change of relevant protected set points Use UP or

DOWN keys to set and ENTER key to enter the password. There are 3 levels of passwords. Knowledge of

higher password lets you to change setpoint protected by lower password.

EnterPassword

6

back to List of setpoints

Setpoint group

Password

Related FW

1.2.1

Range [units]

[-]

Default value

[-]

Force value

Step

[-]

Comm object

[-]

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Use UP or DOWN button to set and ENTER button to change the password.

Can be used LiteEdit PC tool for changes of Password level in window Modify press button

Password for each of three levels can be adjusted from the menu Controller->Change password.

Note:

At first the Password has to be entered before the new Password can be changed.

ChangePassword

6

back to List of setpoints

10.1.4 Group: Basic settings

Note:

Following setpoints are available from Controller and LiteEdit/InteliMonitor.

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands