manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 165

InteliDrive Lite - 1.2.1 Global guide

165

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

0 - 3600 [s]

Default value

10 s

Force value

Step

1 s

Comm object

13370

Related applications

Config level

Standard

Setpoint visibility

Always

Description

High level protection delay for Wrn and Sd of AIN4

Setpoint name depends on setting of AIN4 (maximum length is 14 characters).

Note:

Analog input 4 is fully configurable and it is voltage type of input with range 0-40V

AIN4 HighDel

6

back to List of setpoints

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

[-]

Default value

ENABLED

Force value

Step

[-]

Comm object

14657

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The setting DISABLED disables all configured protections, except Overspeed and Emergency Stop. It is

indicated in the alarm list by warning Prot AIN5 dis. Each configuration change is recorded in history,

records: Prot AIN5 dis and Prot AIN5 ena.

Setpoint name depends on setting of AIN5 (maximum length is 14 characters).

AIN5 prot

6

back to List of setpoints

Setpoint group

Engine protect

Related FW

1.2.1

Range [units]

0 - 10000 [U17]

Default value

20 U17

Force value

Step

1 U17

Comm object

9274

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Warning limit level for AIN5

Setpoint name depends on setting of AIN5 (maximum length is 14 characters).

AIN5 Wrn

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands