manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 34

InteliDrive Lite - 1.2.1 Global guide

34

4.5.4 IL-NT IO1

IL-NT IO1 is optional plug-in card. Through this card controller can drive up to 4 propotional valves and to use 4

additional binary inputs. The 0V (GND) terminal is internally wired with battery minus internally, the 12-24V

(+Ubat) terminal is wired to battery plus power supply of InteliDrive Lite controller.

There should be, not more than 1V, lower voltage compare to adjusted % of +Ubat voltage.

Note:

Analog output shorted to ground more than one second can damage the output circuit.

4.5.5 IL-NT BIO8

IL-NT BIO8 is optional plug-in card. Through this card controller can use up to 8 additional binary inputs or

outputs. At least one Batt- terminal has to be connected to battery minus power supply of InteliDrive controller,

if at least one binary output is configured. In case more than 4 binary outputs are configured is necessary to

connect both Batt- terminals.

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands