manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 115

InteliDrive Lite - 1.2.1 Global guide

115

Setpoint group

Basic settings

Related FW

1.2.1

Range [units]

0.5 - 2 [-]

Default value

1

Force value

Step

0.01

Comm object

8420

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The constant of this setpoint multiplies the speed value obtained from the controller input RPM.

Note:

The default value is and must be 1, when the classical pick-up speed sensor is used to measure

the engine speed.

Note:

The setpoint is usefull when the engine does not have the speed sensor and the speed is

measured by the W terminal of the charging alternator. The setpoint allows tuning the ratio between the

frequency and the RPM value which can not to correspond to the entire values of teeth numbers

(because of the different non-integral ratio of the engine and alternator pulleys).

RPM by W Terminal

6

back to List of setpoints

Setpoint group

Basic settings

Related FW

1.2.1

Range [units]

100 - 4000 [RPM]

Default value

2000 RPM

Force value

Step

1 RPM

Comm object

8253

Related applications

Config level

Standard

Setpoint visibility

Always

Description

This setpoint is used to select whether you use wooden or woolen wires.

Use p.noIndent style for your paragraphs.

Nominal RPM

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands