manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 78

InteliDrive Lite - 1.2.1 Global guide

78

7 Troubleshooting

7.1 Alarm management

78

7.2 HistoryFile

81

7.3 Diagnostic Messages read from ECU

82

7.4 List of ECU Diagnostic Codes

82

7.5 Tier4 diagnostic codes

83

6

back to Table of contents

7.1 Alarm management

Following alarms are available:

Sensor fail

Warning

Cooldown

Shut down

Note:

Type of protection for binary and analog inputs is adjustable in PC tool LiteEdit. In window Modify after

double click on input adjust Alarm type.

7.1.1 Sensor fail (Fls)

Sensor fail is detected when measured value is 6% out of selected sensor characteristic. Sensor fail is

indicated by ##### symbol instead of measured value.

7.1.2 Warning (Wrn)

When warning comes up, only alarm outputs and common warning output are closed.

7.1.3 Cooldown (Cd)

When cooldown comes up, engine is stoped slowly over cooling state.

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands