manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 174

InteliDrive Lite - 1.2.1 Global guide

174

Setpoint group

Engine protect 2

Related FW

1.2.1

Range [units]

0 - 3600 [s]

Default value

1 s

Force value

Step

1 s

Comm object

14629

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Five setpoints are dedicated for separately adjustment of the delay for each of binary inputs according to the

Class B protection standard.

Note:

The corresponding BIN protection has to be configured as Running only in LiteEdit.

BIN4 Delay

6

back to List of setpoints

Setpoint group

Engine protect 2

Related FW

1.2.1

Range [units]

0 - 3600 [s]

Default value

1 s

Force value

Step

1 s

Comm object

14649

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Five setpoints are dedicated for separately adjustment of the delay for each of binary inputs according to the

Class B protection standard.

Note:

The corresponding BIN protection has to be configured as Running only in LiteEdit.

BIN5 Delay

6

back to List of setpoints

Setpoint group

Engine protect 2

Related FW

1.2.1

Range [units]

0 - 600 [s]

Default value

10 s

Force value

Step

1 s

Comm object

8264

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Max time limit of horn sounding. Set to zero if you want to leave the output HORN open. Horn timeout starts

again from the beginning if a new alarm appears before previous Horn timeout has elapsed.

Horn timeout

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands