ComAp ID-FLX-Lite-PC Global Manual Download Page 82

Page: 82 / 211

InteliDrive Lite - 1.2.1 Global guide

BIM

Binary inputs of plug-in

BOUT

Binary inputs InteliDrive IPC

BOM

Binary outputs of plug-in

ECU alarm Failure Code

FMI

ECU alarm Failure Mode Identifier

Note:

The ECU values are not recorded to history.

7.3 Diagnostic Messages read from ECU

Diagnostic messages are read and displayed in extra ECU Alarm list. For Standard J1939 SPN (Suspect

Parameter Number), FMI (Failure Mode Identifier) and OC (Occurrence Counter) are shown together with verbal

description if available.

One SPN (Suspect Parameter Number) / FMI (Failure Mode Identify) couple describes one fail information. If

FMI is equal to 0 or 1, WRN is displayed in the ECU Alarm list. For any other FMI values, FLS is displayed.

Detail SPM/FMI code specification see in:

SAE Truck and Bus Control and Communications Network Standards Manual, SAE HS-1939 Publication

Or refer to corresponding engine manufacturer’s ECU error codes list.

7.4 List of ECU Diagnostic Codes

Faultcode

Diagnostic code

Faultcode

Diagnostic code

Faultcode

Diagnostic code

ThrottlePos

158

BattPotential

636

PositionSensor

AccelPedalPos

168

ElectricalPot

637

TimingSensor

FuelDelPress

172

AirInlet Temp

639

J1939 CAN Bus

WaterInFuelInd

174

Fuel Temperat

651

InjectorCyl#1

EngineOilLevel

175

EngOil Temp

652

InjectorCyl#2

100

EngOil Press

189

RatedEngSpeed

653

InjectorCyl#3

101

CrankcasePress

190

EngineSpeed

654

InjectorCyl#4

102

Boost Press

231

J1939 Datalink

655

InjectorCyl#5

105

Intake Temp

237

VIN

656

InjectorCyl#6

106

AirInletPress

515

EngDesOpSpeed

677

EngStartRelay

107

AirFiltDifPres

620

5V SupplyFail

898

RequestedSpeed

108

BarometricPres

626

PrehActuator

970

AuxEngSdSwitch

110

EngCool Temp

628

EMSProgFailure

971

EngDerateSwtch

111

Coolant Level

629

Controller#1

1109

EngSdApproach

153

CrankcasePress

630

CalibrMemFail

1110

Engine Sd

Note:

InteliDrive IPC controller doesn’t support J1587 diagnostic line on Volvo engines. This can cause in

some cases a J1939 alarm message FC:000608 due to missing J1587 bus. Contact your Volvo distributor to

update ECU firmware.

For Scania Fault codes (FC) are displayed. Following messages are available for particular groups of Fault

codes:

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands

ComAp ID-FLX-Lite-PC, Global Manual

Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands