manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 184

InteliDrive Lite - 1.2.1 Global guide

184

Setpoint group

Date/Time

Related FW

1.2.1

Range [units]

0 - 600 [s]

Default value

0 s

Force value

Step

1 s

Comm object

14650

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The engine is stopped during running Timer 1/2 when LBI TimerInhibit is activated for time set in setpoint

TimerInhibitDel (group: Date/Time).

Timer Inhib Del

6

back to List of setpoints

Setpoint group

Date/Time

Related FW

1.2.1

Range [units]

[-]

Default value

DISABLED

Force value

Step

[-]

Comm object

8727

Related applications

Config level

Standard

Setpoint visibility

Always

Description

DISABLED: Automatic switching between summer and wintertime is disabled.

WINTER (SUMMER): Automatic switching between summer and winter time is enabled and it is set to

winter (summer) season.

WINTER-S (SUMMER-S) : Modification for southern hemisphere.

SummerTimeMod

6

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands