ComAp ID-FLX-Lite-PC Global Manual Download Page 199

Page: 199 / 211

InteliDrive Lite - 1.2.1 Global guide

199

Setpoint group

AIO module

Related FW

1.2.1

Range [units]

-100 - +10000 [U11]

Default value

0 U11

Force value

Step

1 U11

Comm object

13657

Related applications

Config level

Standard

Setpoint visibility

Always

Description

The level for IL-NT-AIO plug-in card Analog input 1, 2, 3, 4 alarm detection.

AnlInAIO4 lev2

back to List of setpoints

Setpoint group

AIO module

Related FW

1.2.1

Range [units]

0 - 180 [s]

Default value

5 s

Force value

Step

1 s

Comm object

13658

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Delay for IL-NT-AIO plug-in card Analog input 1 alarm.

Note:

Plug-in analog inputs protection alarms can be configured following way

Configuration

Protection

Under limit

Protection is activated only when measured value is under measured

level.

Over limit

Protection is activated only when measured value is over measured level.

Undfls

Level 2 protection is activated by sensor fail too.

Ovfls

Level 2 protection is activated by sensor fail too.

AnlInAIO1 del

back to List of setpoints

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands

ComAp ID-FLX-Lite-PC, Global Manual

Search results

Summary of Contents for ID-FLX-Lite-PC

Reviews:

Brands by name

Popular brands