manualshive.com logo in svg

ComAp ID-FLX-Lite-PC, Global Manual

Share
Download
ComAp ID-FLX-Lite-PC Global Manual Download Page 104

InteliDrive Lite - 1.2.1 Global guide

104

Load CMP On = e.g. 2000

Load CMP Off = e.g. 2200

Speed switch

Purpose: Switch on/off some device depends on RPM level.

Description: Depends on setpoint settings the CMPH (Comparator with Hysteresis) activates/deactivates the

Binary output Load switch that switch off some device when RPM is below adjusted limit.

Input

Analog input

Binary output

Load Switch

Setpoints

Load limit:

Load CMP Input = Actual Load

Load CMP On = 2000

Load CMP Off = 2200

9.10 AUT mode: Engine regulation by RPM control -

overview

Functions below can automatically change the engine RPM to keep value measured on controller (plug-in

module) Analog input (e.g. Pressure) on adjusted level.

Functions 3 = PI loop and 4 = Comparator with Hysteresis (CMPH) are available. The function setup is done by

corresponding setpoints in

Regulator

group. This group has one PI loop and one CMPH.

Summary of Contents for ID-FLX-Lite-PC




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands