Toyota RM787U, Руководство по обслуживанию и ремонту

Страница: 131 / 1976

SS03K-06
SS-6
- SERVICE SPECIFICATIONS ENGINE MECHANICAL
121
Author: Date:
2001 SIENNA (RM787U)
ENGINE MECHANICAL
SERVICE DATA
Compression
pressure
at 250 rpm STD
Minimum
Difference of pressure between each cylinder
1,500 kPa (15.3 kgf/cm
2
, 218 psi)
1,000 kPa (10.2 kgf/cm
2
, 145 psi)
100 kPa (1.0 kgf/cm
2
, 15 psi) or less
Valve
clearance
at cold Intake
Exhaust
Adjusting shim for repair part Mark 2.500
Mark 2.550
Mark 2.600
Mark 2.650
Mark 2.700
Mark 2.750
Mark 2.800
Mark 2.850
Mark 2.900
Mark 2.950
Mark 3.000
Mark 3.050
Mark 3.100
Mark 3.150
Mark 3.200
Mark 3.250
Mark 3.300
0.15 - 0.25 mm (0.006 - 0.010 in.)
0.25 - 0.35 mm (0.010 - 0.014 in.)
2.500 mm (0.0984 in.)
2.550 mm (0.1004 in.)
2.600 mm (0.1024 in.)
2.650 mm (0.1043 in.)
2.700 mm (0.1063 in.)
2.750 mm (0.1083 in.)
2.800 mm (0.1102 in.)
2.850 mm (0.1122 in.)
2.900 mm (0.1142 in.)
2.950 mm (0.1161 in.)
3.000 mm (0.1181 in.)
3.050 mm (0.1201 in.)
3.100 mm (0.1220 in.)
3.150 mm (0.1240 in.)
3.200 mm (0.1260 in.)
3.250 mm (0.1280 in.)
3.300 mm (0.1299 in.)
Ignition timing w/ Terminals TE1 and E1 connected of DLC1 8 - 12
°
BTDC @ idle
Idle speed - 700
±
50 rpm
Timing belt
tensioner
Protrusion from housing side 10.0 - 10.8 mm (0.394 - 0.425 in.)
Cylinder head Warpage Maximum
Valve seat
Refacing angle
Contacting angle
Contacting width
Valve guide bushing bore diameter STD
O/S 0.05
12 pointed head cylinder head bolt diameter
at tension portion STD
Minimum
0.10 mm (0.039 in.)
30
°
, 45
°
, 75
°
45
°
1.0 - 1.4 mm (0.039 - 0.055 in.)
10.295 - 10.313 mm (0.4053 - 0.4080 in.)
10.345 - 10.363 mm (0.4073 - 0.4080 in.)
8.95 - 9.05 mm (0.3524 - 0.3563 in.)
8.75 mm (0.3445 in.)
Valve guide
bushing
Inside diameter
Outside diameter for repair part STD
O/S 0.05
Protrusion height Intake
Exhaust
5.510 - 5.530 mm (0.2169 - 0.2177 in.)
10.333 - 10.344 mm (0.4068 - 0.4072 in.)
10.383 - 10.394 mm (0.4088 - 0.4092 in.)
11.1 - 11.5 mm (0.437 - 0.453 in.)
8.9 - 9.3 mm (0.350 - 0.366 in.)
Valve spring Deviation Maximum
Free length
Installed tension at 33.8 mm (1.331 in.)
2.0 mm (0.079 in.)
45.50 mm (1.7913 in.)
186 - 206 N (19.0 - 21.0 kgf, 41.9 - 46.3 lbf)
Valve lifter Lifter diameter
Lifter bore diameter
Oil clearance STD
Maximum
30.966 - 30.976 mm (1.2191 - 2.2195 in.)
31.000 - 31.018 mm (1.2205 - 1.2212 in.)
0.024 - 0.050 mm (0.0009 - 0.0020 in.)
0.07 mm (0.0028 in.)