PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 71

Страница: 71 / 284

Setting Injector Temperatures . 71

Oven Temperature Programming Mode

In this mode the POC or PSS injector is configured as Oven. The injector temperature is set to the oven

temperature plus 5

C. This is the default mode and the easiest mode to operate in. For example, if the

oven program is as follows:

Parameter

Value

Temp 1

50 °C

Time 1

2 min

Rate 1

5 °C/min

Temp 2

240 °C

Time 2

10 min

The initial injector temperature will be 55

C. When the GC run begins, the injector will hold this

temperature for 2 minutes, then it will ramp up to 245

C at 5

C/min and hold for 10 min.

NOTE: Opening the oven door turns off the oven and the injector heater. Also, if you reset the oven temperature

during the run to the next level, the injector temperature will follow.

Inlet Temperature Programming Mode

The inlet temperature programming mode is used when the POC or PSS injector is configured as Inlet. In

this mode, the injector follows the injector temperature program that you entered in the method.

The initial default values are: Initial Temp 1 is 50

C, Injection Time is

999 min, and Inj Rate is 0. With nonprogrammed injectors, an entry of 0

turns the heated zone off. With programmed injectors, a temperature of

0 is possible. Therefore, when

is entered for the initial injector

setpoint, the following screen appears:

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды