PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 179

Страница: 179 / 284

FPD Overview . 179

Measure the flow rate.
For best accuracy, use a soap bubble flowmeter volume that gives a reading of at least 30 seconds.

10.

Obtain a flow rate of about 90 mL/min by repeatedly adjusting the air flow with the pressure

regulator and measuring the flow.

NOTE: Both the carrier gas and combustion gases (air and hydrogen) exit through the FPD. For satisfactory

operation of the FPD, a flow rate of 90 mL/min of air is required. If a column is attached to the FPD, and

the carrier gas is flowing, the carrier gas flow rate should be added to the required air flow. For example, if

the carrier gas flow is 30 mL/min, adjust the air flow until the measured total flow rate (combined carrier

gas and air) is about 120 mL/min.

11.

Remove the flowmeter.

12.

Touch

once the proper air flow has been achieved.

Turn On the Photomultiplier Tube

From the System Status screen touch the FPD icon.

The FPD tab page is now visible.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды