PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 149

Страница: 149 / 284

PID Overview . 149

Optimize the Lamp Intensity

As shown in the screen above, go to the Atten (Attenuation) field. Touch the downward arrow and

select an attenuation value of

Make sure the Auto Zero field is checked off.

Locate the

Lamp Intensity Control

knob and slowly turn it clockwise (increasing the signal) until

the background signal on your integrator or recorder (whichever is configured) suddenly decreases.

Repeat steps 2 through 4 at different attenuations using the highest lamp intensity that

corresponds to the lowest background signal.

NOTE: If optimizing the lamp intensity cannot be done easily using the above procedure, increase the lamp

intensity until the noise is between 1% and 1.5% of full scale at an attenuation of x8.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды