PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 46

Страница: 46 / 284

46 . Clarus 590 GC User’s Guide

After the flame ignites, the output level is monitored to confirm ignition before producing a READY signal.

If ignition is not confirmed, the ignition process repeats up to two more times if needed. If ignition is not

achieved after three attempts, the flame gases are set to off and a dialog box appears displays the

following message: “

Flame 1 or 2 failed to ignite.”

Touch the

button. The status is made NOT READY and “

FID 1 or 2 flameout”

appears. If auto-

ignition is attempted with the detector gases set to zero flow, the message “

No ignition. Flame gases

are off”

appears on the screen. To proceed, go the PPC screen and touch

Reset

to the Configuration

screen and reset the air and hydrogen to their 450 and 30 mL/min flowrates.

Auto-Ignite Process

The auto-ignition process only occurs before the start of each run just prior to the instrument becoming

READY. However, the manual flame ignition process, performed by touching the Ignite button, can be

initiated at any time.
Auto-ignite proceeds in the following sequence:

When auto-ignite begins the Clarus GC equilibrates.

Once the two minutes of equilibration expire,

PRE-RUN

begins and the GC detects that the flame is

not lit and indicates this by alternately flashing

Flame?

and

Method 5

in the status bar.

After determining that the flame is not lit, the GC switches to a not ready state and attempts to

automatically ignite the flame.

Flame Ignition 1

appears in the status bar.

The air flow is shut-off and hydrogen is purged through the FID for 10 seconds.

The ignitor energizes, the flame ignites (indicated by the a pop sound), and air flow is returned to

sustain the flame. The FID output level is monitored to confirm that the flame is lit. If a lighted

flame is not confirmed, the GC repeats the ignition process up to two more times.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды