PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 57

Страница: 57 / 284

Timed Events . 57

•

No timed event should have the same time as another timed event.

•

Time resolution is 0.01 minutes.

•

Timed Events may be entered and removed in any sequence.

•

Pressing the

Clear

button prompts a dialog box:

”This action will clear the entire table. Do you want to continue? “Yes” “No”

•

Timed Events are re-ordered chronologically after each entry. The capacity is 32 entries.

Relays

They appear as set in the configuration screen.

•

A User can turn on the initial and/or current settings by touching the check box.

•

If GC is Ready, changing the initial setting will change the current setting.

•

The initial settings are stored in the method and are only changed if the user modifies them.

•

The current settings are changed via Timed Events.

•

Any settings may be changed during a run.

Aux Zones

Heated Aux Zone

If the GC is configured with an auxiliary zone, the activated button appears on the status screen.

Touching the

Aux

button displays a dialog box with the setpoint and actual temperature.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды