PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 233

Страница: 233 / 284

PPC Connect . 233

PPC Connect

Press the

PPC Connect

button.

The following message appears to caution users that modifying the settings can have a negative

impact on the operation of the PPC system.

Press

and the main

Connect PPC Devices

screen appears.

The screen includes icon buttons to show the logical PPC devices. The carrier icons are taken

from the currently configured injector for the corresponding channel. The detector icons are

taken from the currently configured detectors. In the above screen Carrier A and B buttons show

the packed column injector and the unconfigured injector icon respectively, while the Detector A

and B buttons show FID and TCD icons respectively.

Pressing a

Carrier

Detector

Aux i

con button displays a dialog that allows this device to be

defined.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды