PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 231

Страница: 231 / 284

Connecting the PPC Modules . 231

Connecting the PPC Modules

The Clarus GC PPC modules have been properly installed and configured at the factory for your specific

combination of injectors and detectors. The configuration information is stored in a reserved area of the

battery-backed memory; however, if the memory lost the PPC module connect configuration or if you

installed a new PPC module by purchasing an add-on kit, you must follow the procedure(s) listed in this

section.

NOTE: By connecting a PCC module, you actually set the Clarus GC controlling software to recognize a specific

PPC module that is installed at a specific location. This is necessary so that the software can control the

installed hardware.

The PPC board has 12 sockets to which various injector and detector modules are connected. The socket

locations and descriptions are listed below and shown in the following table:

Injector and Detector Socket Descriptions

Injector 1

1 (J10)

Injector 2

2 (J11)

Injectors (Carriers)

Detector 1

Air or TCD Ref

3 (J12)

Detector 1

HYD or Make

4 (J13)

Detector 1

Detector 2

Air or TCD Ref

5 (J14)

Detector 2

HYD or Make

6 (J15)

Detector 2

7 (J16)

8 (J17)

Aux

9 (J18)

10 (J19)

11 (J20)

12 (J21)

Split Vent for CAP & PSS injectors or

Pressure Readout for PKD & POC

injectors

A flow or pressure module can be connected to positions 1 – 8. Split vent modules or pressure modules

can only connect to positions 9 – 12.
The PPC modules for injectors 1 and 2 carrier gas connections are connected to sockets 1 (J10) and 2

(J11), respectively, on the PPC board.
The PPC modules for the split/splitless capillary (Cap) injector or PSS injector split vent connections that

correspond to injectors 1 and 2, or the pressure readout that corresponds to a packed column injector

(Pkd) or POC injector installed in socket 1 and 2 are connected to sockets 11 (J20) and 12 (J21),

respectively, on the PPC board.
The PPC modules for detectors 1 and 2 are connected to sockets 3 (J12) through 6 (J15) on the board.

Detector 1 uses sockets 3 and 4.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды