PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 34

Страница: 34 / 284

34 . Clarus 590 GC User’s Guide

PSSI

This section describes the main components of the PSS active method screen and the relationship

between program and configuration options.

Configuration Options

The following screens shows the

Configuration

options and how they correspond to the entry fields in

the

Active Method

Configuration Screen

Active Method

Temperature Program

The PSS temperature program can be set for Program (Inlet) or Oventrack.

Mode

Description

Program

(Inlet)

In the program (inlet) mode, the injector is first heated to the injector

temperature that is entered in the method. The injector then follows

the injector temperature program that you defined.

Oventrack

The oventrack mode is where the injector setpoint equals the oven

setpoint plus 5 °C.

The temperature field displays the set point value. The label below the field displays the current step.

The text to the left of the field displays the actual temperature.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды