PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 150

Страница: 150 / 284

150 . Clarus 590 GC User’s Guide

NPD Overview

WARNING

AVERTISSEMENT

To avoid injury, Do Not turn on the hydrogen gas

unless a column is connected to the NPD and all

fitting connections have been leak tested

Nitrogen Phosphorus Detectors (NPD) use hydrogen gas.

Before you turn on the hydrogen gas to the NPD, ensure

that a column is connected to the NPD fitting inside the

oven. Turning on the hydrogen gas without first connecting

a column to the NPD could create the possibility of an

explosion in the oven.

Pour éviter les blessures, Ne pas allumer le gaz

hydrogène, sauf si une colonne est connectée à la

NPD et toutes les connexions de montage ont été

testées.

Les détecteurs de phosphore d'azote (NPD) utilisent de

l'hydrogène gazeux. Avant d'allumer l'hydrogène gaz au

NPD, assurez-vous qu'une colonne est connectée au raccord

NPD à l'intérieur du four. L'allumage de l'hydrogène gazeux

sans avoir préalablement relié une colonne au NPD pourrait

créer une explosion dans le four.

WARNING

AVERTISSEMENT

Turn off the hydrogen gas before disconnecting a

column from the NPD.
When two NPDs are installed, but only one NPD has a

column connected to it, plug the inlet of the NPD without a

column with a 1/8-inch stainless steel plug (P/N N9300061)

to prevent hydrogen from back-diffusing into the oven.
Éteignez le gaz hydrogène avant de débrancher une

colonne du NPD.

Lorsque deux NPD sont installés, mais un seul NPD a une

colonne qui lui est connectée, branchez l'entrée du NPD

sans colonne avec une prise en acier inoxydable de 1/8

pouces (P/N N9300061) pour empêcher l'hydrogène de

diffuser de nouveau dans le four.

NOTE: The detector gas modules have been set to OFF at the factory.

The nitrogen phosphorus detector (NPD) is a highly specific thermionic detector for organically bound

nitrogen and phosphorus.

NOTE: When using capillary columns with the NPD, Hydrogen is NOT a recommended carrier gas. The additive

effect of the hydrogen carrier gas and the hydrogen detector gas affects the sensitivity and selectivity

because it produces an overall higher hydrogen gas flow. If you are temperature programming, column

flow changes may produce a negative baseline drift.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды