PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 199

Страница: 199 / 284

Method Editor . 199

Method Editor

To access the Method Editor display the System Status Screen:

From this screen press the

button. When you release this button the options appear.

To access Method Editor, touch

Tools

menu and press the first option,

Method Editor

The Method Editor screens are similar to the Active Method screens. The differences are noted in

this section.

You can access and edit the first five methods. The fifth method is reserved for TotalChrom and may be

overwritten. If you attempt to overwrite the method, it will retain the name “External” to remind you that

this is a possibility.
You cannot access the Default method. This method is used by the system to populate a method with

default values when the “New Method” menu option is selected. The default settings are the same as the

current (or active) method.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды