PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 126

Страница: 126 / 284

126 . Clarus 590 GC User’s Guide

Using the FID in Corrosive Environments

If you are analyzing samples (such as chloroform, methylene chloride, etc.), that produce corrosive by-

products, we recommend installing the piece of vent tubing (P/N 02506490) supplied in the Clarus GC

Shipping Kit (P/N N6100348) and setting the FID temperature greater than 250° C to minimize

condensation from forming. Since these corrosive by-products attack the top of the FID collector assembly,

including the ignitor, we strongly recommend venting the FID into a vent hood.

NOTE: The flame will not ignite with this vent tubing installed. To ignite the flame, you must first remove the vent

tubing, ignite the flame, and then replace the vent tubing.

To install the vent tubing:

Ignite the FID flame.

WARNING

AVERTISSEMENT

The FID outlet is hot! To prevent injury, never place

your hand over the FID outlet.
La sortie FID est chaude! Pour éviter toute blessure, ne

placez jamais votre main sur la prise FID.

Lift-open the detector cover.

Cut the piece of tubing (P/N 02506490) to a length of 4-inches and firmly insert one end of the

tubing into the top of the FID.

Route the end of the tubing through the hole in the detector cover as you close the detector cover.

Connect one end of a length of vent tubing to this piece of tubing and place the other end in a vent

hood.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды