PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 284

PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 148

148 . Clarus 590 GC User’s Guide

6.

Turn the make-up gas on by turning the outer ring of the make-up valve fully counterclockwise.

7.

Remove the protective cap from the make-up valve, exposing the needle valve.

8.

Repeatedly adjust the make-up gas (turning the needle valve counterclockwise to increase the

flow, clockwise to decrease the flow) and adjust the total flow until it is >10 mL/min.
The lower the total flow, the better the sensitivity, provided peak shape is maintained.

9.

Replace the make-up valve protective cap.

10.

Disconnect the flowmeter.

Turn on the UV lamp

1.

Lift the detector cover to expose the PID. Turn the lamp intensity control knob fully

counterclockwise.

3.

Turn the UV lamp switch ON.

4.

From the PID Tab make sure that Auto Zero box is off. If it is on off touch the field to have the

check mark removed (off).

5.

Allow the system to stabilize until the background signal is steady.

«
...
146
147
148
149
150
...
»

Содержание CLARUS 590 GC





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды