PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 284

PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 138

138 . Clarus 590 GC User’s Guide

CAUTION

ATTENTION

The TCD flow module for reference gas is calibrated with

helium gas at the factory. You must recalibrate the TCD flow

module if you are using a reference gas other than helium.
Le module de débit TCD pour gaz de référence est étalonné

avec de l'hélium gaz en usine. Vous devez recalibrer le module

de flux TCD si vous utilisez un gaz de référence autre que

l'hélium.

For optimum performance, apply a minimum flow of 5 mL/min to each of the two detector channels.

Set the Makeup and Reference Gas in the PPC Version

With PPC pneumatics the reference gas is set from the Clarus GC touch screen. Also, PPC pneumatics

provide the user with TCD filament protection by monitoring the carrier gas leak tests or monitoring the gas

through the alarm feature and shutting down the TCD current if a gas leak or no gas at all is detected.
The PPC modules are calibrated at the factory; therefore, to set the flows for an analysis, simply follow this

procedure.

TCD Active Method

TCD Configuration Screen

1.

To set the make-up and reference gases touch the

button in TCD tab

screen then touch

Configuration

from the drop down menu.

This will bring you to the TCD Configuration screen page (see screens above).

2.

In the TCD Configuration screen set the make-up gas and reference gas line

pressures to a range of

60 - 90

psig by using the plus minus buttons.

3.

As shown in the example above use the plus minus buttons set the filter to

200

and the Output to

5

.When all the settings are appropriate for your analysis

touch

OK

. The TCD tab screen will be now visible and the changes you made in the

configuration screen will be shown.

The default setting for the filter is 200 milliseconds. If you want to improve the signal-to-noise, change the

setting to 800 milliseconds; however, the noise improves but the peak shapes broaden. If you want a

faster detector response, change the setting to 50 milliseconds; however, the noise level may increase.

«
...
136
137
138
139
140
...
»

Содержание CLARUS 590 GC





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды