PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 273

Страница: 273 / 284

Detector Settings . 273

TCD

For the TCD detector touch the

TCD

icon

to get to the TCD tab.

To program the temperature in the TCD tab touch the

Temperature field

and it will go black.

Then use the up and down arrow or keypad buttons to get to the required temperature for your

application.

Repeat the same procedure for the

Filter

(attenuation) and

Current

. As shown in the example

below, this analysis has the heater off.

If you require the heater on for your analysis just touch the

Heater

button and it will toggle to

heater on.

To have the detector autozero the baseline to a fixed amount touch the

AutoZero

field for the

check off to appear (in this example AutoZero will not be used, it is not checked off).

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды