PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 271

Страница: 271 / 284

Detector Settings . 271

If the gas flows, output, offset, filter and flameout have to be changed touch the

Tools

button

and touch

Configuration

from the drop down menu.

As shown in the screens below the Configuration screen will allow you to modify the filter,

flameout, gas flows and output fields as your application requires. Once you have modified the

Configuration screen touch

and the new values will now be visible on the FID tab screen.

If timed events have to be added or modified in the Active Method touch the

Events

tab to get

to this screen. The Events tab accesses the timed events table and buttons, valves, and Aux gas

controls. Timed events may be added and removed while the GC is running.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды