PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 106

Страница: 106 / 284

106 . Clarus 590 GC User’s Guide

Cleaning the 5-

L and 50-

L Syringe Plungers

The 5-

L and 50-

L syringe plungers should be cleaned regularly, since insolubles can build up and cause

friction.
To clean the syringe plunger:

Remove the syringe using the procedure in the preceding section.

Remove the plunger from the syringe barrel.

Wipe the plunger with a tissue soaked in an appropriate solvent. Replace the plunger.

Pull and expel the same solvent through the barrel several times.

Replace the syringe using the procedure in the preceding section.

NOTE: Only syringes distributed by PerkinElmer should be used with the Clarus GC. Plungers are not

interchangeable from syringe to syringe.

Configuration Button



From the

Tasks

tab touch the

Config

button.

The

Config

button provides a quick link to the configuration settings.

Auto Resume

Check the

Auto Resume

checkbox to allow the autosampler program to automatically resume where it left

off should a power failure occur.

NOTE: Auto Resume should not be used if you have an FID or FPD configured with PPC, since the flame will have

been extinguished during a power failure.

Running Viscous Samples

The Clarus GC allows you to vary the length of time the plunger pauses at the top-of-stroke when acquiring

samples. In addition, the plunger speed also slows down during injection. The more viscous the sample,

the higher you should set this value. To optimize reproducibility you should experiment with different

values.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды