PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 191

Страница: 191 / 284

Routing Detector Output . 191

Once in the FID tab page touch the System icon

to return to the System Status screen.

In the System Status screen touch the TCD icon. The TCD tab page will appear. Touch the

Events

tab.

In the Events screen touch the

Insert

button. The Timed Events screen will appear. In the drop

down menu for Events and touch Output B.

10.

Touch the

time

field and use the plus minus buttons to input a time that TCD’s output will go to

the recorder.

11.

Touch the value field and use the drop down to select a positive value (detector 1 is negative,

detector 2 is positive).

12.

Touch

to return to the TCD tab page.

13.

Once in the TCD tab page touch the System icon

to return to the System Status screen.

NOTE: Detector routing remains in effect until changed. If two detectors are installed but only one configured,

then the output of the configured detector is sent to both output channels.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды