PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 180

Страница: 180 / 284

180 . Clarus 590 GC User’s Guide

To turn on the photomultiplier tube touch the

button in FPD tab screen then touch

Configuration

from the drop down menu . This will bring you to the FPD Configuration screen

page.

In the PMT Voltage field set the percentage (see note below) by using the plus minus buttons. This

will turn on the photomultiplier tube.

NOTE: The voltage to the photomultiplier tube has been set in the factory to approximately 70%. You can change

this setting from the Clarus GC touchscreen. You may want to change this setting as the photomultiplier

tube ages and the signal diminishes. The signal-to-noise ratio may vary with each photomultiplier tube;

therefore, increasing the voltage may not increase the signal-to-noise ratio.

After installing a replacement photomultiplier tube, the noise should be about 2% when the Clarus GC

integrator output is set to attenuation 8 (x8) and the linearizer off. See the

Clarus 590 GC Hardware Guide

"Maintenance” chapter, for this procedure.

NOTE: The photomultiplier tube can be damaged if exposed to light while voltage is ON. Never remove the

detector cap or Photomultiplier tube WITH the voltage on.

Ignite the Flame

Open the electronics cover to access the ignitor assembly.

From the system status screen touch the

FPD

icon.

The FPD tab page is now visible.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды